Tampilkan postingan dengan label tool school. Tampilkan semua postingan
Tampilkan postingan dengan label tool school. Tampilkan semua postingan
So I've used a LOT of tools over the years and feel comfortable with all of them. But I still get intimidated when I use a new one! (The tile saw made me sweat the first time, till I realized how easy it was to use!) If someone is interested in learning how to use a new tool I tell them to do two things -- do a ton of research (blogs are a GREAT resource 😉) and take your time and "get to know" the tool before you use it. 

When I'm trying something for the first time I take my time unboxing it and putting it tougher, and read all of the paperwork that comes with it. This helps to ease me into it and makes me feel more comfortable. I also look up videos to see how people use the tool. 

Recently the folks at Dremel asked me to share a DIY project using their Dremel Maker Kit and I was honored they asked...but nervous to try something new!:
Dremel maker kit review for burning and cutting wood

I laugh when I think about that because I feel totally comfortable using my huge compound miter saw but these little Dremel tools were intimidating me. I think it happens to everyone -- and I think it's a good thing because you don't want be overly confident when you use a tool for the first time.

This maker kit comes with three tools -- the Dremel 200 rotary tool, which can be used for a variety of DIY projects. The Dremel engraver is for engraving stone, metal and wood. And the VersaTip soldering torch, which I was most excited about, is for burning into wood, soldering or cutting: 
Dremel three piece tool set

I had a project in mind and I knew either the engraver or the VersaTip would work:
Dremel tool kits

I worked in the garage on a large scrap piece of wood and started trying them out (after reading all the materials on operation). 

I tried the engraver first and it was so cool and incredibly easy to use: 
Dremel engraving tool

I knew right away this wasn't the look I wanted but I am thinking of ways I can use this one on metal or glass in the future. 

I really wanted to give this project a burned look so I decided to try the VersaTip instead. You need to fill the tool with butane -- we already had some for filling our candle lighters. You flip the tool upside down and then press the butane nozzle into it. It only takes a few seconds to fill it up -- you'll feel the canister getting cold: 
Butane Dremel wood burner

You need to let the butane warm up a bit and then it's ready to use! 

It was incredibly easy to operate -- there's a safety switch but once you flip that up it's just like a lighter. You'll hear the torch start burning and you'll see it as well: 
Dremel VersaTip for wood burning crafts

You can smell the butane a bit -- that's another reason you may want to try this project outside. It's not overpowering by any means. This tool comes with a bunch of tips for different projects -- from cutting to soldering to burning. I found this one above to be the easiest for this project. 

On a side note -- I was thrilled to learn that I can use this tool for caramelizing foods as well. I've always wanted to try making creme brûlée at home and now I can! :) 

Once I was comfortable with using the tool, I printed out what I wanted to burn into the wood. A friend of ours is getting married later this year and I thought this would be a cute addition to their gift. I LOVE adding a handmade or personal gift for weddings or baby showers and used to do it a lot. I'm trying to get back to that. :) 

I found a package of wood slices at Michael's for this project and taped the image onto the wood: 
Burning wood with Dremel tool

Then I traced the letters with a pen to transfer the image to the wood like I showed you how to do here. 

On some of them I found it was helpful to trace the imprint with a pen before I started with the tool. I took the paper off (don't leave it on there with a flame!) and started burning the shapes into the wood:
Wedding gift wood coasters

This is not a quick project -- you'll want to take your time and be methodical about it. I started with a lighter hand to get my shape and would go back over it to get the darker burnt look. 

I think they turned out SO cute. I'm kind of in love with them. In my head I made these planning to gift them as coasters so I added a couple layers of wipe on polyurethane:
DIY wedding gift/craft

But really, they could be used in so many ways!

I added some felt stickers to the bottom of each one so they don't scratch: 
DIY wood slice coasters

I tried to do wedding-type images -- their initials, the heart (like one you would see carved into a tree) and the Roman numeral for the day they're getting married and the year: 
DIY wood slice wood burning craft
I think they'll make great coasters! But they could be used in so many other ways too -- I could see them as super cute ornaments if they decide to drill a hole into the top of each one. I also think they'd be fun as art in a shadow box or placed on top of a black background in a frame. They could also be used as small trivets for dishes -- there are so many uses!

I just think they're plain cute and I smile when I see them. The bride and groom are a fun young couple and I hope they'll enjoy them too: 
Wood burning craft/gift with wood slices

I'm so glad I tried this tool and got over being intimidated by something new. Of course after I used it I realized how easy it was! We have a Dremel cutting tool that I've used in the past but this set is more for precision crafts and items where you want to add more detail. I highly recommend it if you are interested in doing those types of projects. 

Have you tried this tool for any crafts or DIY projects? I though it was fun and it wasn't nearly as intimidating to use as I thought it would be. I felt comfortable with it within minutes of trying it out and burning the wood was fun. My mind is swimming with ideas for future projects! Now I'm off to make creme brûlée! ;) 








Wellllll…it only took a year. (I say that a lot don’t I? It only took a month…six months…a year.) And I’m still not completely done. But 98 percent of our doors are rid of their look-away-or-the-shiny-will-blind-you brassiness.

WHOO!!

There’s a few reasons it’s taken so long. First, the order was messed up back when I ordered in February (of 2010!). Second, uhhh…I dunno why. I get easily distracted by other project I guess.

Oh look, a butterfly!

Ha! No really, it’s like that.

So it took a while. I ordered our new oil-rubbed bronze beauties from an online source called Your Home Supply. A sweet reader recommend them and their prices were pretty fantastic. Almost half of what I found at hardware stores.

But there were a couple issues with my order – a few of the knobs had damage, I had accidentally ordered two slightly different bronze knobs (there’s oil rubbed bronze and dark bronze – watch that) and many of the pieces (knobs and hinges) just didn’t arrive.

It took a couple weeks of calling, leaving messages and emails before I called one day and finally got a live person. She was great and took care of getting new knobs out to me really quick…but they still weren’t all there, even in the second batch.

Sheesh. So…I guess I’d say try them out at your own risk? I think if you had an issue, they’d address and fix it, but it may take some time and persistence on your part.

The prices are pretty great – so it may be worth the trouble!

Anyhoo, I’m finally getting the last of the knobs installed. I’ve been meaning to show you this process forever, so here we go!

Here’s a before shot of the brass knobs on my son’s bathroom doors:

I don’t know if I’ve ever showed you that room? It’s pretty darn cute. ;)

There are a few tools you’ll need, depending on your knobs. I needed a pencil, hammer, chisel, Phillips screwdriver and a drill (last two not pictured):

tools for changing out knobs

You may not need the chisel, but more on that in a bit. :)

I start with the hinges – so easy! Use your drill to take the old ones off:

hinges

You don’t need to take the door off – just replace one hinge at a time. Take one old one off, put a new one on.

You may need the hammer to dislodge the old hinge. It’s most likely been there for a while, and it will need a little push to get it off. (I knock it from below the hinge a few times and it works great.)

So once your hinges are on, you’ll be squealing because it already looks so good, but it’s time to move on.

There’s three kinds of knobs – you’ll want to be sure to get the right ones. Privacy knobs are for bathrooms and bedrooms and they lock. Passage knobs don’t have a lock and turn freely – so for closets, etc. Dummy knobs are for spots like double doors – remember you’ll probably need two, one for each side of the door.

This was the door to the bathroom, so it took a privacy knob:

privacy knob

It’s so simple to take the old knob off – just use a Phillips screwdriver to take out the two screws:

Take them out, and the two knobs will come easily apart:

IMG_3507

Here’s where it got a little dicey with my first shot at this…a year ago. :)

Our previous hardware had a small round hole for the latch:

The new hardware did not. :) It had a plate the latch was installed in. I thought this was going to be a major pain in the booty to deal with when I first realized this, it’s not a big deal at all. Hang in there folks…this is the fun part. ;)

Place the new latch in the hole, and hold it in the right spot. Then trace around it:

Then, bust out your chisel and your Tool Man grunt and get to it.

First, place your chisel along your lines, and use a hammer to tap the chisel into the wood, going around your tracing. Then take the chisel and angle it so you can start chipping away at it, again using the hammer as you go:

mortise

You want to mortise out that area so the latch will fit flush, or almost flush. It doesn’t have to be exactly right – just check it as you go. You’ll think you’re taking off a ton of wood, but it would be hard to make it too deep. Just keep checking here and there.

I gotta tell you…using a chisel is way fun. :) It makes me feel all woodsmith-y. I like it. And it’s fun to see the instant gratification with each tap of the hammer.

Once you get the depth right, just screw the latch in:

It’s time to get your new knob, WHOO HOO! It will look something like this:

oil rubbed bronze knob

Just take them apart, and put the part with the long pole into the latch. There’s a curved part on the pole that you’ll want to match up with the curvy part inside the door:

It won’t go in if you have it wrong, so no worries. You just have to match those up. Then place the other side on the back, and put your new screws in:

I use a Phillips for this as well, with towel or rag up against the knob. I didn’t want to chance messing up the finish on the knobs.

Here’s an important tidbit…most times the part of the knob with the screws will go on the inside of the room or the closet. With passage knobs, it doesn’t matter where you put them, but I like having them on the inside of the door.

The important part – ALWAYS, always have a screwdriver with you and stay on the side of the door with the screws while installing. You’ll need to test the door here and there, and once and a while there may be a little something off. Sometimes, not often, but sometimes the door can latch just so in the process and may get jammed. You need to be able to take the knob off (with your screwdriver) if the door gets stuck.

I had a few sweaty moments over the course of changing out all of the knobs in our house. And one of my BFFs may or may not have locked herself in the bathroom when this happened. Not just the bathroom – her little bitty potty closet. We (I?) laugh about it now, but she says it was so scary to be stuck in there, with no way out. (She busted the knob to get herself out.)

So anyway…keep the screwdriver, stay on the screws side, or at least have someone at home while you’re doing it. ;)

OK…we’re almost there peeps!! SO CLOSE. The only little bit left is the strike that’s in the door frame:

The new strike comes with the knob. You’ll just remove the old one, and install the new one like you did the hinges.

This is where you want to heed my earlier advice – you’ll need to test the door with the strike – sometimes things get a bit off in the process and they don’t fit perfectly together anymore.

No biggie – just move the strike around a little, or chisel out a little from behind it, and you’ll be good to go!:

Isn’t she lovely? Isn’t she beautiful? :)

I’m gaga over the contrast of the white doors and dark hardware:

oil rubbed bronze knobs

Right up my alley baby!

I know I give brass a hard time…a little too much of a hard time? Maybe.

Sorry Brass. Nothing against you…I just don’t like ya. Your Antique Brass cousin? LURVE. Shiny you? Notsomuch. I’m so not sad to see you gone. :)

So there you go…even with the mortising, it doesn’t take that long once you get the hang of it. Now I can get the whole door changed out in about 20 minutes. I’ve had a lot of practice over the past year though. :) Only two more to go…and I’m DONE.

If you don’t have to chisel, you could change out these in ten minutes easy. Swear – I promise you can do this!

Here’s the before and after, side by side:

Classy. ;)

I also used the chisel to mortise out the hinges for our new pantry door last fall. It’s the same idea – just trace the hinge, then chisel it out. It doesn’t have to be perfect – it’s covered in the end!

Now that I’m used to using it, I’m want to get my chisel on and make some kind of woodworking masterpiece someday…after I finish the knobs that is. :)


Howdy! Remember when I told you I got a fun new tool, and that tool was the Dremel Multi-Max?

image

(Salivating.)

Well, I told you I’d share the ways I’ve found to use it, and I found some GOOD ones. :)

The tool came with three attachments – two cutting blades and a sander. It was super easy to put them on – just loosen the nut, fit the attachment in and tighten:

IMG_2455

I started with this one:

IMG_2456

And I knew just what I wanted to attack with it:

IMG_2417

We have a few windows in the house that are really showing their age – or at least the caulk around them is. You can see from above that some are not in the best shape. Not so great for the heating bill, I tell you.

I have a goal this winter to recaulk all of our windows, and I have heard to do it right, you need to remove the old stuff first. I was thisclose to ignoring that advice and going right over everything with new caulk – until the Multi-Max. :)

This thing was so stinkin’ cool, ACK!! I just turned it on, slid the attachment in, and let it get under the caulk:

IMG_2419IMG_2418

I turned up the power a bit, and it just slid right under that stuff like butta.

It only took seconds to get a huge piece off:

  IMG_2420  IMG_2415 

And then I did the same along the bottom:

IMG_2422

I put tape down on the window sill at first, thinking I might need it to protect the wood:

IMG_2421

But this thing is stealth. No damage whatsoever. LOVE love love – can you believe I’m excited to tackle all the windows now? Who in their right mind enjoys removing caulk? Me, that’s who.

Next, I attached this baby to the Dremel:

IMG_2423

Buwahahaha! Can you feel the power?? :)

It’s been years since I put up the beadboard in our laundry room, and I still haven’t finished it! Only half the room is done -- but I’m determined to finish it up soon. Actually, I have a little redo planned for that room (if I have my way is going to be a HUGE redo, but we will see). At the very least, I need to get the beadboard done.

The hardest part of the whole installation of beadboard (for me) is removing baseboards. I dream of chunky, thick baseboards in our house, and it would have happened a long time ago, but the builders of our home were serious when they installed them.

They are pain in the PATOOT to remove. I’m talking sweating, pulling, cursing, prying, destroying drywall, crying a little, pain.

So I had an idea – I used the Dremel to cut into the baseboards:

IMG_2425

Like butta.

Then I took it along the top, where the drywall and board meet. I haven’t even pulled out the pry bar yet, but I can already budge them, just with my fingers.

Oh HAPPY DAY! The Dremel will save me much sweating. :) I figure if I keep cutting the baseboards every six inches or so, and then along the top as I go -- it’s going to help tremendously.

Finally, I pulled out the sander attachment:

IMG_2458

I have a Craigslist dresser I’ve yet to show you, because I want to paint it. The seller painted the piece, but it wasn’t sanded at all between coats, so it’s really rough to the touch:

IMG_2427

Since I’m repainting it, I needed to sand it down a bit. (I would have anyway – it’s that rough.)

So I used the Dremel to work on the little, skinny parts:

IMG_2430

Do you KNOW how many times I could have used this in the past? Ugh. I love that you can really get around the curvy parts too:

IMG_2467 IMG_2471

The shape is perfect – it literally just slid around the detail of the drawers, like…wait for it…BUTTA.

My little sanding block can’t compete. :)

My very favorite part is that you turn it on, then you can adjust the power while it’s on:

IMG_2473

I found myself adjusting as I went constantly – it’s so easy to do while you’re using the tool.

So there. you. go. Need a gift idea for the handy guy in your life? The hard to buy for Dad? Grandpa? Or maybe for YOU? (I won’t tell.) This little tool packs a punch – I’m not lyin’ when I say I’m super impressed with it.

Can’t wait to knock some more caulk off the windows! After the holidays, of course. :) No more DIY around here till after January 1st. (I’m writing that down so I will stick to it.)

I’ll be back this week with one more easy Christmas idea, then I’m outtie till after Christmas. :)

Hope your buying, wrapping, cooking, baking and entertaining is all going GREAT! 


Well hello! I’m so glad you like my little memo board as much as I do – totally worth the eight month wait, eh?

You may know by now I’m a tool FREAK. I may have a few of them. Alright…A LOT of them. I have something like 35 screwdrivers – because you never know just the one you’re going to need.

I’ve gotten rid of most of the extra STUFF around here lately…but my tools stay. Even the extra 34 screwdrivers. :)

Step away from the tools.

There’s one in particular I’ve been wanting to try forever. I’ve see bloggers talk about it, and drooled. Seen pictures of what it did, and drooled. Seen the results…DROOL.

And so when I got an email asking if I wanted to try out one of my own, I may have squealed, did a little dance, responded superfast and tried to act cool. When it came in the mail…I finally got to drool over my own:

Dremel multi-max

Ahhh. Just look at it. Isn’t it fantastic?

It’s came with a few little attachments that I had no clue what to do with at first:

But I’m doing searching online, and so far, from what I’ve seen, this little attachment cuts like buttah:

I’ve found a few ways to use the Multi-Max, and I just gotta say…Dad, don’t be jealous. I’ll totally let you come help me do some projects with it. ;)

OK…I’ll let you borrow it.

It’s super precise, so you can cut through drywall, trim and flooring:

Dad and I have a project coming up that will require all of the above. Can you guess what it is? :)

It cuts through grout to repair tiles:

And I know just what I’m using this attachment for:

The Muliti-Max is going to make the project I have in mind take half the time. YIPPEE!

And my favorite part, and the reason I wish I had this years ago:

This baby get’s into corners, crevices, weird angles – I have SO many uses for that one!

So, while it’s charging up, and trying to decide what I’m going to tackle first:

Do you have a Dremel tool? If you do, know someone who does, or if you’ve seen a project it came in handy for…please let me know! If you’ve blogged about it, I’d love to see what you did.

I got video of the Nate Show segment, but the cat was meowing through half of it – you know how they are. :) So I’m going to try it again and I’ll post that and the latest giveaway winner tomorrow!

HOLLA!


Popular Posts